Home > Ni Usb > Ni Usb 6009 Drivers Windows 7

Ni Usb 6009 Drivers Windows 7

Contents

To view your watch list, click on the "My Newsreader" link. Note that the maximum voltage on any one pin is 10V with respect to GND. Section 4, above), you must configure the USB-6009 in MAX. After you have finished configuring the device in MAX, you should close MAX (otherwise an error may occur). [Table of contents] 5 Using USB-6009 in LabVIEW Here is a video that http://pic3nter.com/ni-usb/ni-usb-6009-driver-windows.php

If you are looking for an update , pickup the latest one. It is the scaled value (e.g. Differential coupling is of course more robust against differences in grounding potentials, so it should be the default coupling type. All Rights Reserved.

Ni Usb 6009 Datasheet

The terminals or pins are shown in the NI-DAQmx Device Terminals window, see Figure 9. Language ▼ English Français Nederlands 日本語 Deutsch Español Italiano Português (EU) Português (BR) Dansk Cestina العربية 中文 (漢語) 中文 (汉语) Türkçe Русский Polski Svenska Norsk Suomi 한국말 हिन्दी Română Ελληνικά Magyar ME4031 57.190 weergaven 9:55 Digital Input and Output with NI USB-6211 - Duur: 5:39.

Alle rechten voorbehouden. × United States   INNOVATIONS SHOP SUPPORT COMMUNITY Home Community Home : Discussion Forums : Most Active Hardware Boards : Multifunction DAQ : I need the driver for National Instruments México 11.459 weergaven 3:52 Измерения на базе Data Acquisition Toolbox и устройства сбора данных NI USB 6008/6009 - Duur: 9:52. I'm running matlab 2011a on a windows 7 64 bit machine, NI MAX version 5.0.0f1 is installed and i'm using a NI USB-6009; testing the device on MAX gives me a Ni Usb-6008 Driver Windows 7 In the Test Panels window, select the Voltage Output tab, see Figure 11.

tasks are used also for configurating other I/O devices than the USB-6009. Ni Usb 6009 Examples Figure 16: Selecting physical channel for the task In the window shown in Figure 16, we select ai0, which opens the window shown in Figure 17. Then, you should test the individual channels of the USB-6009 to check that the input signals are detected correctly by the USB-6009, and that the output signals generated by the USB-6009 Feed for this Thread Add to My Watch List What is a Watch List? × What is a watch list?

This has been done in Figure 17, where the default name Voltage has been renamed to meas_speed. Ni Usb-6009 Matlab Analog output (AO): 2 outputs. Application software: LabVIEW, C, or Visual Studio. On Simulink, the session based interface is not accessible at this time.

Ni Usb 6009 Examples

In general, a task represents the configuration of the signal input or signal output operation to be executed by the I/O device. Max sampling rate is 48kS/s (48000 samples per second). 14 bits AD converter (USB-6008: 12 bits). Ni Usb 6009 Datasheet NI USB-6009 - Product Certification Dimensional Drawings USB-6009 - Dimensional Drawings Ask An Engineer Submit your question, view possible solutions, and post to the Discussion Forums, email, or call NI. Ni Usb 6009 Price Figure 5: The wizard has finished the installation of the driver software, and the USB-6009 is ready for use, after you click Finish (Norwegian: Fullfr) If you disconnect the USB-6009 from

Output high is above 2V (with open-drain and push-pull as options). (USB-6008 has only open-drain output.) Counter: 32 bits. http://pic3nter.com/ni-usb/ni-daq-6009-drivers.php The price is 2100 NOK. Figure 8: The Devices and Interfaces item If MAX recognizes the USB-6009, the device appears under NI-DAQmx Devices. MATLAB Central is hosted by MathWorks. Usb-6002

Note how the task value (the magenta coloured line) is propagated through the relevant functions. Inloggen 6 1 Vind je dit geen leuke video? This VI runs with a cycle time of 50ms. http://pic3nter.com/ni-usb/ni-usb-6009-driver-windows-7.php Annuleren Afmelden Bezig...

Figure 20: The DAQmx palette on the Functions palette Single sample at one channel The VI ao_ai.vi is an example of how to read in one single sample from one channel, Ni Usb-6009 Device Specifications Documentation: The following relevant documents can be found at http://ni.com: USB-6009 product home page USB-6009 Data Sheet (which is available from the product home page) Getting Started Guide: NI-DAQmx for USB Thank you for any help you may provide.

The DAQ device should be looked at very much like a steroid-infused IFI controller that instead of controlling via a program you upload to it you control it via the USB

  1. The DAQmx Write function writes the voltage value of the analog output channel as defined in task_ao.
  2. Je kunt deze voorkeur hieronder wijzigen.
  3. Autoplay Wanneer autoplay is ingeschakeld, wordt een aanbevolen video automatisch als volgende afgespeeld.
  4. Saving the configuration The configuration can be saved using the Save button, see Figure 19.
  5. For example, P0.3 is line 3 in port 0.
  6. Make sure it is on the MATLAB path. - Tried reinstalling the Data Acquisition Toolbox - Tried reinstalling Matlab 2011a One other thing.
  7. To prepare for the loopback test, we wire together AI0 and AO0.
  8. This opens the window shown in Figure 14 where you can select the measurement type from a list.

Subject: NIDAQ USB-6009 From: Rob Purser Rob Purser (view profile) 165 posts Date: 9 Sep, 2011 20:26:10 Message: 7 of 10 Reply to this message Add author to My Watch List Output rate is 150Hz (samples/second). 12 bits DA converter. Log in om je mening te geven. Usb 6009 Oem Signal Input Range: Here you select the input range.

Copyright © Chief Delphi Figure 11: The Voltage Output dialog window in the Test Panels window In the Voltage Output dialog window, select any voltage between 0V and 5V. Volgende PID Control with NI USB 6009 - Duur: 6:59. More about the author MATLABinRussia 990 weergaven 9:52 Analog Output with USB-6009 - Duur: 3:18.